10 inch High Definition Color Monitor - HD. Two Y/PB/PR inputs or two RGB inputs
High Definition in-line gun, dot mask CRT (mask pitch: 0.28mm for HTM1003) assures horizontal resolution of 500TV lines.
Beam Feedback System provides long-term white balance stability.
Two Y/PB/PR inputs or two RGB inputs are front panel selectable.
Degauss function permit correction of purity error due to earth's magnetism
CRT circuit protects against over-current and over-load, X-ray radiation or CRT burn.
The HTMI003 can be operated by both AC and DC power supplies.
Exclusive for HD SDI input/output is also available (10-inch: HTM1004).
Input Signal Format
Scanning Lines 1125
Frames per Second 30
Interlace Ratio 2:1
Aspect Ratio 16:9
Horizontal Scanning Frequency 33.75KHz
Vertical Scanning Frequency 60Hz
Input Signal Type
Video R,G,B 2ch selectable on front panel
Y,Pb,Pr 2ch selectable on front panel
Sync Sync/HD 2ch
Input Signal Level
Video Y,G VS: 1.0Vp-p or V: 0.7Vp-p
R,B 0.7Vp-p (White signal is positive)
Sync SYNC +/-0.3Vp-p
Input Impedance 75ohm or high impedance bridge connection
Video Output Level 35Vp-p (CRT drive output level, R-ch video component only)
CRT In-line gun dot-type shadow mask high resolution CRT mask pitch 0.28mm
Screen Size (Wide Screen) 152(W) x 86(H)mm, Aspect Ratio 16:9
Input Voltage AC 100-120V, 50/60Hz single phase
AC 200-240V, 50/60Hz single phase
Power Consumption 90W or less
Installation Place Indoor
Ambient Temperature 0'C - 40'C (+32'F - +104'F)
Relative Humidity 10 - 90% (non-condensing)
Dimensions (excluding gum foot) 222(W) x 213H) x 400(D)mm, 8.7"(W) x 8.4"(H) x 15.7"(D)
Weight Approx. 11kg
Horizontal -Center 500 lines or more
Voltage Fluctuations Stable operation is ensured with +/-10% lines voltage fluctuations referenced
to the rated value.
Frequency Response With reference to the rated output referenced to 500KHz, upto the R,G,B
CRT drive output from the video input terminal
60Hz - 17MHz +1/-3dB
Waveform Distortion With reference to the rated output, upto the R,G,B CRT drive output from
the video input terminal.
Sag : 5% or less (with 60Hz square wave signal)
Overshoot: 5% or less(with symmetrical square wave signal of line frequency
of 10nS rise time.
Aperture Correction +6dB or more is adjustable at 10MHz +/-5MHz with maximum aperture
Noise Synchronous : -46dB or more
Random : -50dB or more
Hum : -50dB or more
Sync Stability Stable operation is ensured within +/-6dB referenced to the rated value.
Deflection Amplitude Adjustable to the rated picture size with an aspect ratio of 16:9.
Deflection Distortion Within +/-1% of picture height(both deflection linearity and raster distortion)
Horizontal (H) 10mm or more
Vertical(V) 10mm or more
Horizontal(H) 12% or less
Vertical(V) 6% or less
Hum Oscillation 0.2mm or less
Tolerance 20KV +/-1KV
Regulation With reference to 100uA for fluctuations of 0 to 300uA +/-3% or less
Convergence 0.4mm or less inside a circle with diameter of 90% of picture height
0.5mm or less inside a circle with diameter of 90% of picture width